wiki:Component/VciMultiAhci

Version 27 (modified by alain, 7 years ago) (diff)

--

SocLib Components General Index

VciMultiAhci

1) Functional Description

This component emulates a multi-channels disk controller respecting the AHCI standard. Each channel[k] can access a different physical disk, modeled as a file (one file per channel) belonging to the host system, and containing a complete disk image. Each channel[k] can perform data transfers between file[k] and a buffer in the physical memory of the virtual prototype. The number of supported channels, the file name(s), the VCI burst size, and the block size are hardware parameters, defined as constructor parameters. The number of channels cannot be larger than 8. The burst size must be a power of 2 between 8 and 64 bytes. The block size must be a power of 2 between 128 and 4096 bytes.

According to the AHCI specification, each channel[k] controller uses a private Command List implemented in the kernel memory. For each channel[k], the associated Command List can register up to 32 read or write concurrent commands, that are handled by the channel controller.

This VCI component has a DMA capability, and use it to access both the Command List and to transfer the data to or from memory.

On the VCI side, it supports both 32 bits and 64 bits data words, and up to 64 bits address width.

For each channel[k], a single IRQ[k] can be (optionally) asserted when one (or several) command(s) in the Command List completes. WARNING: the IRQ[k] is associated to a specific channel, but not to a specific command.

This hardware component checks for segmentation violation, and can be used as a default target.

2) Command List

For each channel, the VciMultiAhci driver must use a specific Command List to register a command: The Command Descriptor array (32 entries) define the Command List. Each Command Descriptor occupies 16 bytes, and must be aligned on a 16 bytes boundary. It contains mainly the physical address of the associated Command Table. A command Descriptor is defined by the following C structure:

typedef struct hba_cmd_desc_s  // size = 16 bytes
{
    unsigned char       flag[2];        // WRITE when bit 6 of flag[0] is set 
    unsigned char       prdtl[2];	// Number of buffers
    unsigned int        prdbc;		// Number of bytes actually transfered
    unsigned int        ctba;		// Command Table base address 32 LSB bits
    unsigned int        ctbau;		// Command Table base address 32 MSB bits
} hba_cmd_desc_t;

3) Command Table

There is one Command Table for each Command descriptor. For a given command, there is one single LBA (Logic Bloc Address) on the block device, coded on 48 bits, but the source (or destination) memory buffer can be split in a variable number of contiguous buffers. Therefore, the Command Table contains two parts: a fixed size Header, defining the LBA, followed by a variable size array of fixed size buffer descriptors. The Command Table describing one command is defined by the two following C structures:

typedef struct hba_cmd_header_s // size = 16 bytes
{
    unsigned int       res0;        // reserved	
    unsigned char      lba0;	    // LBA 7:0
    unsigned char      lba1;	    // LBA 15:8
    unsigned char      lba2;	    // LBA 23:16
    unsigned char      res1;	    // reserved
    unsigned char      lba3;	    // LBA 31:24
    unsigned char      lba4;	    // LBA 39:32
    unsigned char      lba5;	    // LBA 47:40
    unsigned char      res2;	    // reserved
    unsigned int       res3;        // reserved	
} hba_cmd_header_t;

typedef struct hba_cmd_buffer_s // size = 16 bytes
{
    unsigned int       dba;	    // Buffer base address 32 LSB bits
    unsigned int       dbau;	    // Buffer base address 32 MSB bits
    unsigned int       res0;	    // reserved
    unsigned int       dbc;	    // Buffer byte count

} hba_cmd_buffer_t;

4) Addressable registers

Each channel[k] contains six 32 bits read/write registers:

  • HBA_PXCLB

32 LSB bits of the Command List physical base address. This address must be aligned on a 16 bytes boundary.

  • HBA_PXCLBU

32 MSB bits of the Command List array physical address.

  • HBA_PXIS

Channel status, used for error reporting.

31302928.....2423..........87.....10
--R -- CMD_ID BUFFER_ID -------D

Bit[0] : set by hardware when at least one command has been completed. Bit[30] : set by hardware when an error has been detected in a command. Bit[28:24] : index of the faulty command in command list (set by the hardware). Bit[23:8] : index of the faulty buffer in the faulty command (set by the hardware). When an error is detected for a command, the R bit is set, the channel FSM stops immediately, without handling the remaining commands in the command list, and keep blocked, waiting for a software reset on this PXIS register.

Any write access to this register reset all bits to 0, whatever the VCI WDATA value.

  • HBA_PXIE

This register enables and disables the IRQ reporting the completion (success or error) of the commands for a given channel. Only 2 bits are used:

313029 ...................................... 10
--R ------------------------------------D

Bit 0 : when set, an IRQ is generated when bit0 of AHCI_PXIS is set. Bit 30 : when set, an IRQ is generated when bit30 of AHCI_PXIS is set.

  • HBA_PXCMD

Boolean : Writing a non zero value activates the polling of the Command List. Writing a zero value makes a soft reset on PXCI, PXIS, PXIE, and PXCMD registers.

  • HBA_PXCI

Bit-vector, one bit per command in the Command List. These bits are handled as 32 set/reset flip-flops: set by software when a command has been posted in Command List / reset by hardware when the command is completed. A write command on this register makes a OR between the VCI WDATA field and the current value of the register.

For extensibility issues, the software drivers must use the mnemonics defined here to access this component .

Even if there is only six registers per channel, each channel sub-segment occupies 4K bytes, and the HBA segment must be aligned on a 32 Kbytes boundary.

5) Component definition & usage

source:trunk/soclib/soclib/module/connectivity_component/vci_multi_ahci/caba/metadata/vci_multi_ahci.sd

6) CABA Implementation

CABA sources

CABA Constructor parameters

VciBlockDevice(
     sc_module_name name,   //  Component Name
     const soclib::common::MappingTable &mt, // MappingTable
     const soclib::common::IntTab &srcid,    // Initiator index
     const soclib::common::IntTab &tgtid,    // Target index
     const std::vector<std::string> &filenames, // vector of filenames (one per channel)
     const uint32_t block_size = 512, // block size (bytes)
     const uin32_t burst_size = 64,  // burst size (bytes)
     const uint32_t latency = 0);  // initial access time (number of cycles)

CABA Ports

  • sc_in<bool> p_resetn : Global system reset
  • sc_in<bool> p_clk : Global system clock
  • VciTarget<vci_param> p_vci_target : VCI target port
  • VciInitiator<vci_param> p_vci_initiator : VCI initiator port
  • sc_out<bool> p_irq : Interrupt port
  • sc_out<bool> p_sdc_clk : SD Card clock
  • sc_out<bool> p_sdc_cmd_value_out : CMD bus value to SD Card
  • sc_out<bool> p_sdc_cmd_enable_out : CMD bus enable to SD Card
  • sc_in<bool> p_sdc_cmd_value_in : CMD bus value from SD Card
  • sc_in<bool> p_sdc_cmd_enable_in : CMD bus enable from SD Card
  • sc_out<bool> p_sdc_dat_value_out[4] : DAT bus value to SD Card
  • sc_out<bool> p_sdc_dat_enable_out : DAT bus enable to SD Card
  • sc_in<bool> p_sdc_dat_value_in[4] : DAT bus value from SD Card
  • sc_in<bool> p_sdc_dat_enable_in : DAT bus enable from SD Card

7) TLM-DT Implementation

Not available yet.